Vehicles
84 not categorized PORSCHE 356B REAR PLATECan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91450109010 If you notice bubbling at the back of the threshold plate where it meets the rear quarter panel, the sill is rusted. If you remove the brushed aluminum or black plastic threshold, you will probably see additional damage. Our sill completely solves the problem and is easily welded in. View/Change Diagram
From $55.65
Make a selection FT24076 Our 911 sanden kits offer many benefits over the original york compressor found on the early 911 and 930 up through 1983. The sanden uses a "wobble-plate" to move five smaller pistons as compared to the york that uses a crankshaft to move two large pistons. The sanden wobble-plate design requires less horse power to turn and is a better match for the condenser area. Our sanden kit uses less engine compartment space and less horse power to turn. You will notice it runs smoother and quieter and improves system efficiency. The sanden compressor and it's mounting bracket bolt directly to the original york sub-plate. You can purchase our sanden kits in four configurations to match your objectives and budget: from...(choose a part on the right to read more) General Fitment911 1978-83930 1975-77 911 1974-77
$735.98
Make a selection 94411691100 Does your 924 tach needle climb in high gears and not move the car like it should? Does your 924 make a grinding noise in neutral? Does your 944 seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
$635.49
Make a selection 95111691100 Does your 924 tach needle climb in high gears and not move the car like it should? Does your 924 make a grinding noise in neutral? Does your 944 seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
From $264.50
Make a selection BEK9146 Now you can once again achieve the factory ride and handling long missing from the 914-6 factory offering. Kit includes two factory replica front strut inserts, two factory replica shock absorbers, two rear spring plates, and two factory replica standard springs. bolt on package that will give you the ride and handling the Porsche engineers designed into the car.
$500.00
Make a selection BBI9818200001 Bbi autosport Porsche 981 Cayman GT4 streetcup roll bar features 4130 chrome moly steel tubing for excellent strength to weight ratio and addresses issues such as harness angle, seat travel, and engine compartment access. Taking a sensible design approach, the bar mounts to frame structure in the cabin and rear strut towers to provide the strongest mounting points and maximum protection. For superior strength and rigidity, high strength 4130 chrome moly steel tubing was used throughout and all joints are meticulously tig welded by hand. Bolt-in installation is accomplished by using inner diameter tube clamps that are cnc turned and milled for a precise fit. These unique joints eliminate the unsightly through-bo...(choose a part on the right to read more)
$2,395.00
Make a selection 94411600004 Does your 924 tach needle climb in high gears and not move the car like it should? Does your 924 make a grinding noise in neutral? Does your 944 seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. General Fitment944 1985-88
From $752.02
Make a selection CPO011KP Ksport kontrol pro fully adjustable coilover kits provide the ultimate in suspension technology for your street or track car. 36 levels of dampening adjustment allow you to fine tune the ride to your handling and comfort needs. The dampening adjusts compression and rebound simultaneously for ease of adjustment. Pillow ball top mounts in the front and rear on some applications allow you to maintain vehicle manufacturer suspension geometry design. The pillow ball top mounts also allow you a more direct feel for solid driver response. Camber adjustability is included on pillow ball top mounts that allow it for the ability to adjust camber from the actual coilover, instead of a separate camber kit. General Fitment911 TURBO/GT2 2001-05
$2,049.30
Make a selection CPO020RR Ksport version rr damper system is built specifically for road racing only. Aggressive rates and valving are chosen for maximum handling and performance with acute reaction and responsiveness. Integrated with 36 levels of dampening adjustment, simultaneous compression and rebound adjustment, lightweight aluminum mounts, and pillow ball upper mounts on some applications. (race use only.) General FitmentBOXSTER 1997-04
$2,732.40
Make a selection FVD343986PSS9 Only for vehicles equipped with bilstein suspension pss9/10. General FitmentCAYMAN 2009-12CAYMAN 2006-08 BOXSTER 2009-11 BOXSTER 2005-08 BOXSTER 1997-04
$2,046.79
Make a selection FVD3439642PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,204.50
Make a selection DASRB2NS Das sport bolt-in roll bar Porsche 996/997 (w/o sunroof) 99+ General Fitment911 1998-05
$2,018.25
Make a selection FVD343996PSS9 Only for vehicles equipped with bilstein suspension pss9/10. General Fitment911 1998-05
$1,744.90
Make a selection FVD351997GT2CS This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads. This system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca). General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09
From $3,335.20
Make a selection FVD351997GT2CS2 This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads ( for cars with central lock only ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 8 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$7,021.30
Make a selection FVD351997TTCS1 This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$5,871.80
Make a selection FVD505123964RS Rear bumper center section race look for Porsche 964/965 turbo General Fitment911 1989-94
From $399.00
Make a selection FVDBS352993002 Make your next service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Oem set of rear pads (4 total) 2 qty. Oem brake warning sensor 8 qty. Oem brake pad damping plate (for 28 mm piston) please note: this kit does not contain brake discs!
$240.90
Make a selection FVD512997GT3RST 997 GT3 rear spoiler fits 997turbo includes: deck lid, aluminum upright, 3rd brake light housing and kevlar/carbone wing (l= 145cm, b=28cm, h=7 cm) with end plates. Material: aluminum, fiberglass, kevlar-carbone. Also available with wing blade in fiber (gfk) FVD512997gt3rs tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x
$6,528.50
Make a selection FVDBSK352993001 Make your next service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 2 qty. Rear rotors (zimmermann) 1 qty. Oem set of pads (4 total) 2 qty. Oem brake warning sensors 4 qty. Oem brake pad damping plates (for 34 mm piston) 4 qty. Oem brake pad damping plates (for 30 mm piston) sold as a kit. 1 necessary per car.
$477.40
Make a selection FVD512997GT3RS2 997 GT3 rear spoiler fits all 997 (not turbo) includes: deck lid (grp), aluminum upright, 3rd brake light housing and kevlar/carbon wing (l= 145cm, b=28cm, h=7 cm) with carbon rsr look end plates. Material: aluminum, glass reinforced plastic (grp), kevlar-carbon. Also available with wing blade in fiber (grp) FVD512997gt3rs tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x General Fitment911 GT3 2007-11911 2009-12 911 2005-08
From $3,704.70
Make a selection FVDBSK352970001 Set contains: - brake discs rear left and right - brake pad set - screws for caliper - warning contacts - damping plates
$742.50
Make a selection FVD512964008RS Made in europe by one of the manufacturers to Porsche. Extremely high-quality glass fiber komposite (gfk) rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight - glass fiber komposite (gfk) - mounting is just like factory, no modifications are necessary. - fits all 964 narrow body models - left and right side exits for exhaust please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. If you do not have the rs license plate light please also order 91163162004 General Fitment911 1989-94
From $1,306.37
Make a selection M500041 Moton club sport damper system Porsche 996 turbo 01-05 General Fitment911 TURBO/GT2 2001-05
$8,166.15
Make a selection JWST914PVT Durable, adjustable replacement for the rear trunk pivot. Bolt-in replacement does not require welding to install. Back-up plate reinforces the mounting area. The original pivot mount must be drilled or ground away and four new holes drilled for installation. Strong, smooth pivot will not bind or gall as can occur with the original design can be used with original torsion bars or aftermarket gas shocks. General Fitment914 1970-76
$59.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |